circuitsan-youtube

Simple Crystal Tester Circuit Diagram. Most electronics project working with high frequency utilizes crystal in order to generate frequency as oscillator. It is used instead of coil. Coil can be checked with multi-meter if there is any fault, but checking of crystal completely is difficult. In order to solve this problem a simple project using few components is designed call crystal tester.

This circuit consist two NPN transistors, two diode with few passive component. The crystal under test is combining with transistor T1 which further work as oscillator. The combination of transistor T1, crystal under test and capacitors C1 and C2 is work as colpiitt oscillator. If the testing crystal is good then it works as oscillator with transistor T1. The output of oscillator is rectified and filtered by diode D1 and capacitor C2 respectively and given to base of transistor T2. The signal given to base conduct transistor which further glow the LED connected to the collector through resistor R3. If the testing crystal is faulty then LED1 does not glow.

PARTS LIST
Resistors (all ¼-watt, ± 5% Carbon unless stated otherwise)
R1 = 27 KΩ
R2 = 1 KΩ
R3 = 560 Ω
Capacitors
C1 = 0.001 µF
C2 = 100 pF
C3 = 0.001 µF
C4 = 0.004 µF
Semiconductors
D1, D2 = 1N4148
T1, T2 = BC550C
LED1 = Green
Miscellaneous
SW1 = push to on switch

Build a Flashing Light with Twilight Switch Circuit Diagram. Flashing light is very useful in order to indicate any obstruction or working in progress. The project automatic flashing light with twilight switch flash light in dark but during day it automatically turns off itself.

The circuit diagram of automatic flashing light with twilight switch is shown below where LDR is used as sensor. In the presence of light LDR offer low resistance and in dark it offers high resistance. When there is absence light, LDR offer high resistances which turn off the transistor T1. Due to this darlington pair made from transistor T2 and T3 is turn on which further glow bulb. The feedback from its output is given to the junction of resistor R2 and LDR as shown in circuit diagram. Due to feedback this circuit works as oscillator which work as flasher. Variable resistor VR1 is used to adjust the sensitivity of LDR.

 

 

PARTS LIST
Resistors (all ¼-watt, ± 5% Carbon unless stated otherwise)
R1 = 2.2 KΩ
R2, R3 = 1 KΩ
R4 = 3.3 KΩ
VR1 = 25 KΩ
Capacitors
C1 = 1 µF – 10 µF
Semiconductors
T1, T2 = BC547B
T3 = BEL187-P
Miscellaneous
LDR
B1 = 3V to 10V bulb

Simple Automatic Water Pump Controller Circuit Diagram is a series of functions to control the Automatic Water Pump Controller Circuit in a reservoir or water storage. As the water level sensor made with a metal plate mounted on the reservoir or water tank, with a sensor in the short to create the top level and a detection sensor for detecting long again made the lower level and ground lines connected to the bottom of reservoirs or reservoir. 

The series of automatic water pump controller is designed with 2 inputs NOR by 4 pieces and relay that is activated by the transistor. Automatic water pump circuit requires +12 VDC voltage source and can be used to control the water pump is connected to AC power . Here is the complete series of pictures.

R1 = 15K

R2 = 15K

R3 = 10K

R4 = 1K

D1 = LED

D2 = 1N4148

Q1 = BC337

IC1 = 4001

SW = SPDT Switches

Relay RL1 = 12V

How to Build a100W Inverter 12V to 220V Circuit Diagram. When use the electric appliances that want 220V AC 50HZ, which have small-sized about 100Watt not exceed. By when you apply outside home, as a result have to have Mini power inverter about 100Watt, perform modify from work electricity forces of battery 12V give tall fair the work. 

 If you are New user electronics or want to economize or want to build electronics project use by oneself. I begs for to advise this circuit , because it uses , transistor number BC557 or the number replaces, perform oscillator generator. Then have power transistor 2N3055 numbers perform to drive coil transformer for converter voltage give tall go up 220V AC 50HZ at the electric power about 100 watt not exceed. When apply to transformer about 2A-3A. Picture circuit detail and like model PCB Board.

Sourced By www.circuitsstream.blogspot.com

This is a simple TV audio video transmitter circuit can be constructed using this schematic diagram . This TV audio video transmitter circuit can be used to transmit video signals from VCR ( or some other device ) to a TV without using any cable .

Video signals input at jack J1 are first terminated by resistor R6 and coupled through capacitor C1 to clamping-diode D1. Potentiometer R3 is used to set the gain of the video signal; its effect is similar to that of the contrast control on a TV set.

Bias-control R7 can be used to adjust the black level of the picture so that some level of signal is transmitted, even for a totally dark picture.

RF-transformer T1 and its internal capacitor form the tank circuit of a Hartley oscillator that's tuned to 4.5 megahertz. Audio signals input at J2 are coupled to the base of Q3 via C2 and R4: the audio signal modulates the base signal of Q3 to form an audio subcarrier that‚s 4.5-megahertz higher than the video-carrier frequency.

The FM modulated subcarrier is applied to the modulator section through C5 and R9.
Resistor R9 adjusts the level of the subcarrier with respect to the video signal.

Transistors Q1 and Q2 amplitude modulate the video and audio signals onto an RF-carrier signal. The operating frequency is set by coil L4, which is 3.5 turns of 24- gauge enameled wire on a form containing a standard ferrite slug.

The RF output from the oscillator (L4, C7 and C9 ) section is amplified by Q5 and Q6, whose supply voltage comes from the modulator . Antenna matching and low-pass filtering is performed by C12, C13, and L1.

Resistor R12 is optional; it is added to help match the output signal to any kind of antenna.
To align this audio video transmitter you need to tune a TV receiver to an unused channel between 2 and 6. The TV must have an indoor antenna connected directly to it; an outdoor antenna or cable won't work. Make sure both potentiometers (R3, R7) are in middle position and apply power to the transmitter. Adjust L4 with a nonmetallic tool until the TV screen goes blank ,then fine-adjust L4 for the "most-blank" picture.
Connect the video and audio outputs from a VCR(AV source) to jacks J1 and J2 (respectively) of the transmitter .

After that you should see a picture on the TV screen: if you do, readjust L4 for the best picture; if you don't, check the board for any bad connections. Next, adjust R3 for the best picture brightness and R7 for the best overall picture.

Finally, adjust T1 with a nonmetallic tool for the best sound .
The TV transmitter combines line level audio and video signals, and transmits the resulting signal up to 300 feet. The circuit can be powered from a 9-12V power supply circuit .

 

Whereas it's traveled 11.6 billion miles to interstellar space, Voyager 1's software isn't as high-tech as you may believe. In detail, it has less than 40 KB of recollection. To put that in viewpoint, your 16 GB iPhone 5 has about 240,000 times the recollection of a Voyager spacecraft.

NASA developed Voyager in the 1970s in a pre-computer era when scientists had to rely solely on pencil, paper, chalkboards and their own mathematical abilities. While that appears unimaginable in a time when we contain decades' worth of computational power in our pouches, Voyager 1 is one of NASA's most thriving missions, and project researcher Edward Stone states he wouldn't have changed a thing.

"It's astonishing it's continued as long as it has," pebble notifies Mashable. "I don't know how we could have done things much better than they were finished. I mean things do wear out, and we've had to swap to some of our backup schemes, but luckily we have backup schemes. That was part of the wonderful conceive of Voyager."

That thriving conceive is due, in part, to Jupiter. The team took a nine-month detour to ascertain each circuit and part to ensure it could withstand the strong emission it would face in the planet's demanding natural environment.

"That was sort of our life test," Stone says. "Having survived Jupiter, in a certain sense, meant we had designed a spacecraft with a very robust answer to natural, slow degradation."

Thirty six years after launch, NASA has turned off some of Voyager 1's functions — some due to degradation, other ones easily because they're unusable in its present natural natural natural environment. For demonstration, the group turned off Voyager 1's camera — which broke the famous fair blue dot image — because it's too dark to arrest a photo in interstellar space.

Researchers still obtain faint (but exciting) facts and figures from Voyager 1 as it journeys through an unexplored district of space. The spacecraft communicates back to soil utilising a 22.4-Watt transmitter — the matching of a frig lightweight bulb. When those signals come to soil — which takes about 17 hours traveling at the pace of lightweightweight — they are about 0.2 billion-billionth of a Watt.

Although, when it comes to battery life, Voyager 1 has a leg up on the iPhone (and just about any other consumer electrical devices, for that matter). The spacecraft has a plutonium power provide that brags an 88-year half life, meaning we'll stay in feel for years.

"It's a very simple, long-lived source of power, but finally it will run out," pebble states. Unfortunately, Voyager 1 won't have a charger to plug in to when that time rolls around — between 2020 and 2025.